Page 1 of 1

internal technical links

Posted: Tue Feb 22, 2011 2:42 am
by Volker_P
I start here a collection of internal links to important topics. More for my personal usage, however maybe helpful for others, too.
Volker_P



Most important link of this forum: viewtopic.php?f=4&t=5848&start=5 :lol:


2nd important: Cold start procedure: viewtopic.php?f=4&t=727&start=9

Several 1981 issues missing in the Cosky manual might be looked up here: viewtopic.php?f=3&t=5512


brakes

small hole in front master cylinder: viewtopic.php?f=4&t=2383 viewtopic.php?f=4&t=13972

scheme of master cylinder parts: viewtopic.php?f=4&t=1804

dimensions of 1981 Custom front caliper pistons: viewtopic.php?f=2&t=4927&start=12


carbs

jay_kent's proposal how to get them off easier: viewtopic.php?f=4&t=3067

pod filter jetting suggestions for PD/piston carbs: viewtopic.php?f=4&t=773

links to choke cam and triple tee pictures: viewtopic.php?f=4&t=1945

links to adamb's pictures of CV carbs (vacuum shutoff): viewtopic.php?f=4&t=1360

pictures on carb related hoses and a very helpful picture of an installed vacuum shutoff by kullin:: viewtopic.php?f=4&t=4036, viewtopic.php?f=4&t=4162

links to T-vent drawing and pictures: viewtopic.php?f=4&t=8865&start=7 viewtopic.php?f=4&t=4747 viewtopic.php?f=4&t=5890&start=10

how jaynesm soldered the air cutoff holes to avoid splitting carbs and buying diaphragms: viewtopic.php?f=4&t=722 (page three there)
hint by totaled108 which cutoff channels are important to be plugged: viewtopic.php?f=4&t=8781&start=6

soos about different carb and carb boot options (for 79/80 cyl. head): viewtopic.php?f=4&t=722

float height measurement: viewtopic.php?f=4&t=1342, viewtopic.php?f=4&t=6472

carb leakage options: viewtopic.php?f=4&t=4807

an (external) article about disassembling the CV (81-on) carbs: viewtopic.php?f=4&t=5056

how to pull pressed in slow jets of CV carbs: viewtopic.php?f=4&t=4492&start=66

PD carbs: parts interchange options by MiGhost: viewtopic.php?f=4&t=6553&start=3


tank

mechanical and chemical tank cleaning suggestions: viewtopic.php?f=4&t=1411

fuel tank interchange options (on RC05 frame): viewtopic.php?f=3&t=4072


engine

Starter clutch, parts (CMS) and proceeding: viewtopic.php?f=4&t=242

neutral switch cleaning: viewtopic.php?f=4&t=3079&p=20506

Ibsens cam chain tensioner swap with many pictures, hint to misaligned cam chain tensioner: viewtopic.php?f=4&t=74

Where to check cam chaintension directly with a screwdriver: viewtopic.php?f=4&t=8853&start=28

picture of oil dipstick with ruler: download/file.php?id=1969

scheme of head cover bolts with copper washers: viewtopic.php?f=4&t=3070

part numbers of valve spring washers/seats: viewtopic.php?f=4&t=4396

head oil leak: support ring for O-rings: viewtopic.php?f=4&t=2953

CB650 overbore pistons still available (7/2012) here: viewtopic.php?f=3&t=6861


exhaust

muffler disassembly by pinhead: viewtopic.php?f=4&t=261


electrics

a very good (external) link how to check your charging system viewtopic.php?f=4&t=8388

ignitors/CDI's refilled with JBweld by chuter: viewtopic.php?f=4&t=2290

interior of the starter relay: viewtopic.php?f=4&t=4051&p=32809

rotor and stator compatibility and resistance data: viewtopic.php?f=4&t=5080

good quality rotor rebuild for reasonable prices (may require some patience, however): viewtopic.php?f=4&t=1276 (possibly also some money for your dead rotor so don't throw it away!)

ignition lock and switch with clamps picture: viewtopic.php?f=4&t=6765&p=44997


front fork

front fork pitting repair with industrial quality stuff: viewtopic.php?f=4&t=6463

1981 air assist front fork seal replacement: viewtopic.php?f=4&t=523