1980 CB650 Jet Problems

If it's broken or just needs tweaked

Moderators: Volker_P, tidd650

firestopper13
Posts: 6
Joined: Thu Mar 22, 2012 9:42 pm

1980 CB650 Jet Problems

Postby firestopper13 » Thu Mar 22, 2012 10:40 pm

Hi, I'm Bobby. I'm new to this forum. I have searched for info on my bike to no avail, so here goes. Sorry for the novel to follow...

I recently bought a 80 CB650. It ran at idle. Only revved with choke closed. I took the carbs apart to clean them. I found that the slow/pilot jets are pressed in. Someone before me thought they were threaded and cut grooves across them to get them out. Also on two of the slow jets, it looked like someone punched a phillips head into the orifice.

Dum-dum before me scrapped the stock airbox and put pods on it. It has a custom box still attached but no 4 to 1 from carb to intake to mount up. I was successful in fabbing one from pvc before i found the jet problems.

I know i need to up my jets to keep the pods or uni's or even k&n's. Preferably a 120 main and a 42 slow. I do have the option to drill them but again, i would like to keep the stocks.

I have a few questions here. First, where the heck can i get new slow jets that press in? I can't find them anywhere. I believe the carb is a PD50 slide style Keihin.

Secondly, If i am unable to find these jets, would it be easier to drill and tap the orifice for a different style of jet or just get a new set of carbs.

And at last, If new carbs are best, what would i need to do/which year and size of donor bike do i need to look for? I believe the CV carbs would work fine but i am lost.

I am used to working on drag cars or old pickups, not SOHC-4, 32 year old motorcycles. I do, however, love the look and simplicity of these older bikes.

Any help is greatly appreciated.

Bobby
Attachments
CB650.jpg
$300 project bike.
CB650.jpg (193.52 KiB) Viewed 12567 times

onepieceatatime
Posts: 323
Joined: Wed Nov 02, 2011 5:12 am
Location: Franklin County, Pennsylvania, USA

Re: 1980 CB650 Jet Problems

Postby onepieceatatime » Thu Mar 22, 2012 10:50 pm

Welcome.

I cannot help on the jets, as I have not done anything with them myself, but the CV carbs from an 81 or 82 will not work to replace the PD carbs unless you replace the head too. A 79 cb650 has the same PD carbs.
Here is a link to a free online manual for the bike:
http://cosky0.tripod.com/

good luck
Folsoml wrote: Good judgement comes from experience. Experience comes from bad judgement. :lol:


1977 CB750K
1977 CB750K
1978 CB400A
1980 CB650C
1980 CB650
1982 CB900F
1982 CM450A
1997 GL1500SE

firestopper13
Posts: 6
Joined: Thu Mar 22, 2012 9:42 pm

Re: 1980 CB650 Jet Problems

Postby firestopper13 » Thu Mar 22, 2012 11:04 pm

Thanks for the welcome...

I already have that page bookmarked. haha However, i was trying to get away from the press in slow jet. I found a 1980 cb750 with cv carbs but don't know if they will fit. smdh....

For a $300 bike, i felt i got a good deal until i cracked into the carbs.

User avatar
Volker_P
Posts: 5508
Joined: Mon Mar 06, 2006 1:53 am
Location: southern Germany

Re: 1980 CB650 Jet Problems

Postby Volker_P » Fri Mar 23, 2012 4:47 am

Welcome here, Bobby! :D

For pod filter jetting suggestions including sources of supply, please have a look at the 79 cb650 carb jetting question thread by emy111. The pressed jets may be pulled with pliers. Also 1981 CV carb slow jets are still pressed, only 1982 were screwed.
The carb number may be found at one side of the carbs near the floater bowl seam.

In fact the CV carbs would be more foregiving with pods, however as already stated above, they won't line up with the 79/80 cylinder head intake ports. In the 79' cb650 carbsthread member soos provided some interesting carb options for the 79/80 head including how to make the CV carbs fit.

As you probably already found out, mounting the carbs is no fun. So clean out the tank. If you don't get it really clean, install an inline filter. The filter screen of the petcock is too coarse.
Cosky's great (free) online manual: http://cosky0.tripod.com

forum links to common technical issues

If you really like this site and you would not like to see it vanish soon, have a look there: Urgent: Future of HondaCB650.com Forum

firestopper13
Posts: 6
Joined: Thu Mar 22, 2012 9:42 pm

Re: 1980 CB650 Jet Problems

Postby firestopper13 » Fri Mar 23, 2012 1:10 pm

I have all of the jets removed. I have cleaned every orifice that is visible, and cleaner has made its way through every orifice visible. My concern is that the pressed in/friction/slow jets are warped. they look like this () instead of this O. Previous owner smooshed the hell out of them.

Thanks for the emy111 link. I found his website about 2 weeks ago. Dude has some pretty sick cafe's.

Sure would like to run a cv carb but really don't feel like changing heads.

I have drilled out jets for my drag car during race day when i didn't have the right size jets (altitude change i forgot to compensate for) but dang, these are some pretty small holes...

User avatar
Volker_P
Posts: 5508
Joined: Mon Mar 06, 2006 1:53 am
Location: southern Germany

Re: 1980 CB650 Jet Problems

Postby Volker_P » Sat Mar 24, 2012 6:44 am

I would assume the jets were squeezed during a pulling effort with pliers. Probably useless now, will run similar like with blocked idle jets.
Which means stays alive at idle only with choke, insufficient throttle response and and all that stuff. Better get suitable new ones and press them in carefully.
Cosky's great (free) online manual: http://cosky0.tripod.com

forum links to common technical issues

If you really like this site and you would not like to see it vanish soon, have a look there: Urgent: Future of HondaCB650.com Forum

firestopper13
Posts: 6
Joined: Thu Mar 22, 2012 9:42 pm

Re: 1980 CB650 Jet Problems

Postby firestopper13 » Mon Apr 02, 2012 11:39 pm

Well, I have the bike running without choke. After a test run about 9 miles, the bike runs spectacular, until i try to gas it from about 55 mph on. This was resolved later after i removed my custom intake. The bike seemed to run rich which was confirmed after a plug chop.

I drilled the slows out to .016 in. or .40 mm(size 40 jet). i also put 122.5 main jets in for now until i get the 120s.

I took the intake off and proceeded to do another plug chop with a new set of ngk plugs(d8ea) and found the plugs to be a nice tan to brown color.

My only concern now is a little bit of smoking from either the number 1 or 2 cylinder. I believe it to be excess fuel(rich running) but i ran out of time tonight to pull the plug.

Just an update for those of you concerned. :D

User avatar
Volker_P
Posts: 5508
Joined: Mon Mar 06, 2006 1:53 am
Location: southern Germany

Re: 1980 CB650 Jet Problems

Postby Volker_P » Tue Apr 03, 2012 1:16 am

firestopper13 wrote:I drilled the slows out to .016 in. or .40 mm(size 40 jet).

It's not that simple. Jet numbers are a flow measure and not just related to the hole diameter.
Cosky's great (free) online manual: http://cosky0.tripod.com

forum links to common technical issues

If you really like this site and you would not like to see it vanish soon, have a look there: Urgent: Future of HondaCB650.com Forum

cb650
Posts: 2959
Joined: Fri Mar 03, 2006 7:20 am
Location: Denver CO USA
Contact:

Re: 1980 CB650 Jet Problems

Postby cb650 » Tue Apr 03, 2012 5:59 am

There is a argument on what the hole size stands for on sohc4 right now.
FYI the stock jets for a 79/80 is 90.
Did you clean the tank out?!?!?!?!

User avatar
Volker_P
Posts: 5508
Joined: Mon Mar 06, 2006 1:53 am
Location: southern Germany

Re: 1980 CB650 Jet Problems

Postby Volker_P » Tue Apr 03, 2012 6:39 am

In fact the diameter in 0.01mm is not too far off. Maybe this was the early definition. So it might work.
Nevertheless today calibration is done by flow. But sorry, no information on the calibration conditions.

Stock PD51 carbs should have 92 main jets and 35 slow jets.
Cosky's great (free) online manual: http://cosky0.tripod.com

forum links to common technical issues

If you really like this site and you would not like to see it vanish soon, have a look there: Urgent: Future of HondaCB650.com Forum

cb650
Posts: 2959
Joined: Fri Mar 03, 2006 7:20 am
Location: Denver CO USA
Contact:

Re: 1980 CB650 Jet Problems

Postby cb650 » Tue Apr 03, 2012 7:59 am

My manual and bike has pd 50 carbs with 90 jets. might be the USA epa BS.
Did you clean the tank out?!?!?!?!

firestopper13
Posts: 6
Joined: Thu Mar 22, 2012 9:42 pm

Re: 1980 CB650 Jet Problems

Postby firestopper13 » Tue Apr 03, 2012 8:07 am

Don't wanna get in the jet size vs flow debate, but all I'm saying is what i did works for me. The bike runs great.

cb650
Posts: 2959
Joined: Fri Mar 03, 2006 7:20 am
Location: Denver CO USA
Contact:

Re: 1980 CB650 Jet Problems

Postby cb650 » Tue Apr 03, 2012 11:13 am

Yes I hate the what jet to use ? as so many people have their own ideas and think what they did is right. So many things come into play and often overlooked.
Did you clean the tank out?!?!?!?!

User avatar
Volker_P
Posts: 5508
Joined: Mon Mar 06, 2006 1:53 am
Location: southern Germany

Re: 1980 CB650 Jet Problems

Postby Volker_P » Tue Apr 03, 2012 12:08 pm

cb650 wrote:My manual and bike has pd 50 carbs with 90 jets. might be the USA epa BS.

Right, my book says 90 for te PD50B carbs, too. :wink:

As written, the size/bore correlation is not too far off and will probably work for any effort related to trying out for a non stock configuration. Even jets of different manufacturers seem to differ although they carry the same size number. Then they change fuel consistency (ethanol etc.) which also has an impact on flow so finally you have to try out and of course the "bore scale" is not that bad for a relative estimate.

But you can't say e.g. drill a 0.9mm hole and you certainly have the stock main jet. However if you have e.g. 0.85, 0.90 and 0.95mm, there is a good chance that one of them will probably be like stock.
Cosky's great (free) online manual: http://cosky0.tripod.com

forum links to common technical issues

If you really like this site and you would not like to see it vanish soon, have a look there: Urgent: Future of HondaCB650.com Forum

thwrightstuff
Posts: 1
Joined: Sat Apr 18, 2015 1:54 pm

Re: 1980 CB650 Jet Problems

Postby thwrightstuff » Fri Jul 24, 2015 3:24 pm

Hey guys, I am also new to this forum and forums in general. My apologies for reviving such an old thread.

I, too, have a 1980 Honda CB650C and am finally getting around to properly tuning the carbs. My biggest problem are the press fit pilot jets on this bike. I have a MAC 4-1 with an 18'' Quiet-er Core exhaust and I would LOVE to get my pod filters on this bike instead of using that stupid airbox. I have issues with 1/4 throttle, a bit of bog, and my acceleration pretty much goes flat over 1/2 throttle. I know I have multiple problems here, but the main thing first is how do I adjust the press fit slow jets? Do I actually drill them out or try to find other jets and yank them out and install new ones? My fear is that I'll damage the hole for the jet.

Again, sorry for not allowing this thread to die, I just figured my issue is so directly related to the OP's.

Thanks for the advice!


Return to “Technical Discussion”

Who is online

Users browsing this forum: No registered users and 47 guests