Search found 323 matches
- Sun Jan 27, 2019 8:45 am
- Forum: General Discussion
- Topic: '82 cb650sc project
- Replies: 82
- Views: 103522
Re: '82 cb650sc project
Thanks for commenting Skiwatcher, I was beginning to think this forum was only frequented by volker, sweety, and bots! I also wondered if the readership was mostly into factory correct restorations, because nobody comments on this one. I welcome comments both for and against, it's all part of the a...
- Thu May 26, 2016 10:15 am
- Forum: Technical Discussion
- Topic: Turn Signal - aftermarket replacements
- Replies: 7
- Views: 9497
Re: Turn Signal - aftermarket replacements
The striped wires are for the running lights, orange for left and blue for right. Those would need to be capped off, if you do not plan on using them, and the solid orange and solid blue would go to the positive on your new signals, and the ground of the signals to the chassis ground. Also, with LED...
- Thu May 26, 2016 9:50 am
- Forum: Technical Discussion
- Topic: Turn Signal - aftermarket replacements
- Replies: 7
- Views: 9497
Re: Turn Signal - aftermarket replacements
The front turn signals were a 2 element bulb, one for running lights, the other for turn signal. The ground connection for the bulbs was from the chassis through the housing.
Here is a color wiring diagram:
http://www.oregonmotorcycleparts.com/fi ... 50_79_.jpg
Here is a color wiring diagram:
http://www.oregonmotorcycleparts.com/fi ... 50_79_.jpg
- Fri May 30, 2014 7:07 pm
- Forum: Technical Discussion
- Topic: Fork swap
- Replies: 17
- Views: 15772
Re: Fork swap
cb650 wrote:You want to sell it? I might be able to figure something out. Aussie you want to try it?
Sorry to step on your post.
Sure, I don't need it.
- Thu May 29, 2014 10:14 pm
- Forum: Technical Discussion
- Topic: Fork swap
- Replies: 17
- Views: 15772
Re: Fork swap
how far off are they? I could slot the holes or drill a new set. What about the fuse block? '80 cb650 http://i.imgur.com/ij8JOzS.jpg '82 (if I remember the year correctly) 750F http://i.imgur.com/it6WtPc.jpg The lower part of the handlebar clamp, on the top tree, is taller by about .5 inch on the 7...
- Wed May 28, 2014 9:09 pm
- Forum: Technical Discussion
- Topic: Fork swap
- Replies: 17
- Views: 15772
Re: Fork swap
cb650 wrote:cool let me know if you come across it unless the OP wants it.
I found the 750 tree I have, but it is from a 750F, not a C or SC. 37mm forks, ignition mount the same, but the gauge mount spacing is different, so it still wont work correctly to keep original gauges.
- Mon May 26, 2014 5:49 pm
- Forum: Technical Discussion
- Topic: Fork swap
- Replies: 17
- Views: 15772
Re: Fork swap
cb650 wrote:...Nice to know. I might just keep the forks and lower and look for a 750 upper.
I might have one...
- Sun May 25, 2014 9:16 pm
- Forum: Technical Discussion
- Topic: Fork swap
- Replies: 17
- Views: 15772
Re: Fork swap
Aussie wrote:... Also need to know how much oil goes in them air forks if anyone knows as I lost my PDF manual when my computer crashed and can't seem to locate another.
- Sun May 25, 2014 9:12 pm
- Forum: Show it off
- Topic: 1980 CB650 Custom
- Replies: 15
- Views: 13295
Re: 1980 CB650 Custom
I have the original shop manual along with the promotional brochure and was looking through the spec's this morning. Interesting that of all the spec's listed it doesn't state the horsepower. Does anyone know what the actual hp is? I have only seen information listed on a couple of websites. http:/...
- Thu May 22, 2014 4:01 pm
- Forum: Technical Discussion
- Topic: Electrical issues...help!
- Replies: 34
- Views: 20976
Re: Electrical issues...help!
I forgot to mention, but none of the CB650s I have had (2 '80 standards, '80 custom, '81 custom, and '82 standard) have the harness extender to the ignition switch. Maybe it was added to your bikes for a fairing or radio at some point?
- Thu May 22, 2014 3:51 pm
- Forum: Technical Discussion
- Topic: Electrical issues...help!
- Replies: 34
- Views: 20976
Re: Electrical issues...help!
I apologize, I was incorrect. The grounded nuts are used on the standard model, and the custom model the headlight bucket is grounded through a female spade connector on the harness to a male spade connector on in the headlight bucket (rusted off in my picture below because I haven't restored this b...
- Wed May 21, 2014 9:57 pm
- Forum: Technical Discussion
- Topic: Electrical issues...help!
- Replies: 34
- Views: 20976
Re: Electrical issues...help!
Your picture is too small for me to see, but you should have two greens, a brown, and a black left over after everything is plugged in. It looks like you have an extra green. Another thread suggested that the green ground wire should attach to one of the bolts mounting the bucket. This is how 2 of ...
- Wed May 14, 2014 7:35 am
- Forum: Technical Discussion
- Topic: More Mystery Extra Parts
- Replies: 4
- Views: 4601
Re: More Mystery Extra Parts
It goes under the bike, near the swingarm, and connects to the bottom of the airbox. I don't remember exactly where it bolts to, but that might help figure it out. I'll try to look at mine later, if nobody can give a better answer first. http://www.servicehondapsn.com/fiche_section_detail.asp?sectio...
- Sat Apr 12, 2014 6:52 am
- Forum: Technical Discussion
- Topic: Minus the petcock...
- Replies: 26
- Views: 17283
Re: Minus the petcock...
A guy on another forum has put together rebuild kits That are supposed to work for the '82 650s.
Here is a link to the post.
http://www.cb1100f.net/modules.php?name=Forums&file=viewtopic&t=73943&highlight=
Here is a link to the post.
http://www.cb1100f.net/modules.php?name=Forums&file=viewtopic&t=73943&highlight=
- Sun Apr 06, 2014 6:47 pm
- Forum: Technical Discussion
- Topic: Charging System Issues
- Replies: 36
- Views: 17035
Re: Charging System Issues
flamdchicken wrote:Also my ignition modules are nice and melty but still seem to work alright (but charging system isnt working right now).
Common problem as well. Some have re-filled them with JB weld. If they are still working, no need to replace.